TThe eXtremeAir® is the high speed hand dryer for the next generation™. This patented design is the most compact and affordable high speed hand dryer made in the U.S.A. Made of a one-piece 18 gauge stainless steel cover with a #4 brush finish, the GXT Series is GreenSpec listed as energy efficient. It is available in a surface or ADA compliant recess mount.

Operation of the ExtremeAir® GXT Series:
The GXT Series is a high performance hand dryer that is 43% smaller than old “industry standard” high speed dryers; yet, it’s just as powerful and uses less electricity. The 5/8 HP, 24,000 RPM motor produces an adjustable air velocity of 10,000 - 16,000 LFM. The EXT sound levels and drying times are also adjustable. The sound level is adjustable from 83 – 69 decibels. Adjust the dry time from a minimum of 10 seconds. The microprocessor controlled infrared sensor turns the dryer on when hands are under the outlet for up to 80 seconds if needed. The surface mount dryer has a profile of 5-5/8” and is provided with conduit entrances for both between wall and surface wiring.

The ExtremeAir® GXT Series Design:
The patented design is the most compact and affordable high speed hand dryer made in the U.S.A. The GXT is made of a one-piece 18 gauge stainless steel cover and is finished with a #4 brush. Tamper resistant screws secure the cover to steel base making the motor and heater inaccessible, and the air intake vents are shielded for additional safety. The motor is a powerful series commutated through-flow discharge vacuum motor/blower with an automatic resetting thermal protector. The automatic sensor is a RoHS compliant lead-free design and the heating element has an automatic thermal protector that operates in the black range for maximum life producing temperatures up to 135°F. With the new Universal Voltage, you can connect the eXtremeAir® to any voltage 100 - 240 vac, 50 or 60 Hz. Each GXT Series Dryer will require a dedicated 20 amp line.

Optional Recessed Mounting Kit:
The GXT Series also offers a recess mounting kit. It requires a 14-1/2”W x 19-1/2”H rough wall opening and has a profile less than 4” making this fully ADA compliant. The same vandal resistant design includes a wall panel in the same finish and tamper resistant screws.

Optional Universal Adapter Plate:
Should you need to cover a large existing hand dryer installation site, this 14 gauge stainless steel plate (14”H x 16”W) will do it. It will cover the holes from older bulky hand dryers and paper towel dispensers being replaced.

Specifications:

• One piece 18 gauge stainless steel cover
• #4 brush finish
• Automatic Sensor
• Surface or Optional Recessed Mount
• Universal Voltage 100-240 vac / 50 or 60 Hz
• 10 Second Drying Time
• Adjustable Air Velocity: 10,000 - 16,000 LFM (Linear Feet per Min.)
• Air Temp: 135°F
• Adjustable Sound Level: 83 – 69 Decibels
• Shipping Weight: 11 lbs.
• Surface Mount Dimensions: 10-1/8”W x 9-3/8”H x 5-5/8”D
• Recessed Mount Dimensions: 13-1/4”W x 11-7/8”H x <4”D
• Maintenance free
• 5 year limited warranty

A little about your hand dryer installations: Dryers should be placed at least 2 feet apart and at least 12” from the washbasin. (Do not install dryer over washbasins.) Automatic dryers should be at least 18” above any projection which may interfere with the operation of the automatic sensor. Hand dryers require a dedicated circuit (max. 20 amp) and must be properly grounded. One side of dryer should be mounted to stud. For average traffic washroom, we recommend 1 dryer per 2 washbasins, if heavier traffic, 1 dryer per washbasin. If you have enough traffic for a 54” wash fountain, 4 dryers should be installed per sink.